ISO 9001 & ISO 13485 Certified Tangxia, Dongguan · China

Washers, Discs & Rings

Flat washers · discs · collars · retaining rings

Aluminum · Steel AutomotiveElectronics

Thin flat parts look like the easy job and are not. The difficulty is rarely the diameter — it is flatness. A washer that cups, a disc that springs back after parting, a collar that goes out of parallel once the stress is released: that is where thin parts fail.

We deal with it by controlling how the part is held and how it is released rather than by quoting an unrealistic flatness and hoping. Where flatness genuinely matters, tell us the number and how it is measured — often the requirement is real but the way it was written into the drawing is not what the assembly actually needs.

Flat Parts We Make

Flat and plain washersStandard and non-standard, with burr-free faces.
Discs and shimsThin parts cut to a specified thickness and flatness.
Collars and flangesTurned with a controlled bore, face and shoulder.
Retaining and circlip ringsGrooved or plain rings to your drawing.
Spacers and shim packsSupplied as sets where a stack-up tolerance has to be hit.
Conical and curved washersWhere the part is deliberately not flat.

Turned or stamped — we quote the cheaper route

We run both processes under the same roof: CNC lathes, and 13 pneumatic and mechanical presses from 16 to 110 tonnes. A thin flat part with a loose tolerance usually belongs on a press; a thick part, a tight bore, or a small quantity usually belongs on a lathe. Because we do both, we can quote the route that costs you less instead of the one our machines happen to be free for — and where the volume sits on the boundary between the two, we will quote both so you can decide.

Washer & Disc Specification

Machining tolerance±0.01 mm standard, on the dimensions you mark as critical
FlatnessDiscussed per part — thin discs are quoted against how flatness will be measured, not against an assumed number
Thickness rangeEffectively unlimited on turned parts; stamping suits thin stock
ProcessesCNC turning · stamping & punching (16–110 t presses) · secondary milling where needed
MaterialsSteel · stainless 303/304/316 · brass · aluminum 6061-T6/6063
Edge conditionDeburred as standard — no sharp edges left on the part
Surface finishingSandblasting, zinc and nickel plating, blackening, anodizing, passivation
VolumePrototypes from 5 pcs · MOQ 100 pcs per part number · high volumes on stamped parts
Write flatness the way you will measure it. “Flat within 0.05” means something different on a surface plate than in a fixture, and different again for a part 200 mm across versus one 5 mm across. Tell us how the part is checked and we will quote to that — and tell you if a tighter number is achievable in a way that is worth paying for.

Washers, Discs & Rings — Common Questions

Should my part be turned or stamped?
As a rule: thin and high volume goes on a press; thick, tight tolerance, or low quantity goes on a lathe. Send the drawing and the annual volume and we will quote the cheaper route — or both, where the volume sits on the boundary.
How do you control warpage on thin discs?
By controlling the setup and the release of the part rather than by post-processing. Tell us how flatness is measured and we will quote against that measurement.
Can you hold ±0.01 mm on a thin part?
Thickness and diameter can be held to ±0.01 mm on turned parts. On a very thin disc, flatness is usually the harder requirement — so tell us which of the two actually matters.
What materials are available?
Steel, stainless 303/304/316, brass and aluminum 6061-T6/6063, with plating or passivation where the application needs it.
Do you deburr the parts?
Yes, all parts are deburred as standard.
Have a part drawing? Get a quote within one working day. Send a STEP, DWG, DXF or PDF file — or post us a sample. You will hear back from the engineers who will actually make the part. Request a Quote →