ISO 9001 & ISO 13485 Certified Tangxia, Dongguan · China

Pins, Shafts & Studs

Stepped shafts · knurled pins · threaded studs

Stainless · Carbon Steel AutomotiveMachinery

Shafts and pins are unforgiving parts. A washer can be a few hundredths out and still work. A shaft that is out of round, or whose second diameter does not run concentric with the first, turns into a vibration, a bearing failure or a rejected assembly.

We turn them in a single setup wherever the geometry allows, so concentricity holds across every diameter rather than being re-established between operations. Where a part is too long to hold that way, we will tell you which dimension is at risk and how we plan to control it.

Pin & Shaft Work We Run

Stepped shaftsMultiple diameters, shoulders and grooves turned in one setup.
Knurled pinsStraight or diamond knurl, for grip and press-fit retention.
Threaded studsSingle- and double-ended, with rolled or cut threads.
Dowel and locating pinsStraight diameters with chamfered or radiused ends.
Spacers and standoffsCut to length, square and deburred on both faces.
Grooved and slotted partsCirclip grooves, cross-holes and driver flats.

Shaft & Pin Specification

Machining tolerance±0.01 mm standard, held on the dimensions you mark as critical
ConcentricityControlled across tandem diameters machined in the same setup
Machining diameterØ1–40 mm daily range, up to Ø46 mm by process review
Max workpiece length1.5 m on the horizontal lathes
StraightnessDiscussed at quotation for long, slender parts — send the length-to-diameter ratio and the straightness you need
MaterialsStainless 303/304/316 · carbon steel 20#/45#/12L14 · brass · aluminum 6061-T6/6063
Ends and featuresChamfers, radii, centre holes, threads, knurls, cross-drilling and flats
Heat treatmentArranged to your specification where the part needs it; hardness testing can be supplied

Sending us the fit, not just the diameter

A shaft is only correct in relation to the bore it goes into. If you tell us the mating part — a bearing, a bushing, a housing — and the fit you need, we machine to it and check it. If you send a bare diameter with no tolerance callout, we will ask, because a shaft that measures right and fits wrong is the most expensive kind of correct.

For long, slender parts, the length-to-diameter ratio decides whether ordinary turning or Swiss-type turning is the better route. Send us the geometry and we will quote the process that holds the part, rather than the one that is easiest to quote.

Pins, Shafts & Studs — Common Questions

How do you control concentricity on a stepped shaft?
Where the geometry allows, all diameters are machined in a single setup so the relationship between them is fixed by the machine rather than by a re-chucking operation. Where that is not possible, we tell you which dimension is at risk and how it will be checked.
What material should I choose for a pin?
Stainless 303 if it has to machine and resist corrosion, 304 or 316 where the environment demands it, and carbon steel where strength and cost matter more than corrosion. Tell us the load and the environment and we will recommend one.
Can you hold a shaft to a specific fit?
Yes — give us the mating bore or bearing and the fit you need, and we machine and inspect to it.
What is the maximum length you can turn?
Up to 1.5 m on the horizontal lathes. Length-to-diameter ratio matters more than pure length; send the dimensions and we will confirm which process suits it.
Can you supply hardened parts?
Heat treatment is arranged to your specification where the part needs it, and hardness testing can be supplied with the shipment.
Have a part drawing? Get a quote within one working day. Send a STEP, DWG, DXF or PDF file — or post us a sample. You will hear back from the engineers who will actually make the part. Request a Quote →